Bring a Stormbox online

After your installer wires a Stormbox, claim it for its machine in the MonsoonOS admin, connect it to Wi-Fi, switch it on and send a test.

Every planStormbox
Plans
Available on every MonsoonOS plan: Full Wash Platform and Rain Pay Terminals Only.
Needs
You need a Stormbox.
Who can do this:
On Full Wash, anyone whose role includes "Set up machines" (Owner by default). On Terminals Only, your admin login.

A Stormbox connects a machine to MonsoonOS, so a payment, the app or your team can start it. Your installer mounts and wires the Stormbox, following the install sheet that comes with the hardware. This article covers your part in the MonsoonOS admin: claiming the Stormbox for its machine, connecting it to Wi-Fi, switching it on and testing it.

Before you start

  • The machine added in Machines. See Add a machine.
  • The Stormbox installed, wired and powered on by your installer.
  • The Stormbox's serial number, printed on its label.
  • The name and password of the site's 2.4 GHz Wi-Fi network, if the Stormbox will use Wi-Fi.

Open the Configure Stormbox page

  1. Go to Operations › Machines. With several locations, choose one from Location at the top of the page to see only its machines.
  2. On the machine's row, select Configure.

The Configure Stormbox page for that machine opens. You can also reach it from the Setup Guide: the Bring your Stormboxes online step lists every machine with a Configure Stormbox button.

Claim the Stormbox

  1. Under Stormbox Link, type the serial number from the Stormbox's label.
  2. Select Claim.

A message confirms the Stormbox is claimed and linked to this machine. Stormbox Link now shows the Stormbox's status, its serial number and Last contact.

One Stormbox can run several machines. For the second machine on the same Stormbox, choose the Stormbox from the Select a claimed Stormbox… list instead, then select Assign.

Connect it to Wi-Fi

Once the Stormbox is claimed, a Wi-Fi card shows its connection, its Network and the machines it runs. A new Stormbox with a cellular backup comes online over cellular by itself, so you can set its Wi-Fi from here.

  1. In the Wi-Fi card, select Set up Wi-Fi. If a network is already set, the button says Change Wi-Fi.
  2. Type the Network name exactly as it appears, capital letters and spaces included.
  3. Type the Wi-Fi Password, then type it again in Confirm password. Tick Show password to check what you typed.
  4. Select Continue.
  5. Read the summary. The Stormbox restarts and is offline for about 2 to 5 minutes, and its machines cannot start a wash until it is back.
  6. Select Restart and join.

The card shows progress while the Stormbox joins. When it is done, the card shows Online and the new network.

Switch it on and save

  1. Turn on Stormbox Enabled. When it is on, the machine is in service for customers. When it is off, the machine is out of service and hidden from customers.
  2. Select Save Configuration.

Stormbox configuration saved. appears at the bottom right. The wiring settings lower on the page are filled in by your installer from the install sheet. Leave them as they are. A count-down bay, whose own timer counts the wash down, has a few settings of its own: see Set up a count-down bay.

Test the machine

  1. Make sure the bay is clear.
  2. Select Test Pulse. On an in-bay automatic the button says Test Wash Start and starts a real wash, so MonsoonOS asks you to confirm first.
  3. Watch the machine start.

A message at the bottom right confirms the test was sent. Test Connection checks that MonsoonOS is ready to send commands to the Stormbox. To see when the Stormbox itself last reported, read Last contact under Stormbox Link.

When the test works, the machine is ready to sell. Pair its terminal next: Pair an Experience terminal or Register an MDB card reader.

Emergency Stop Lockout

Emergency Stop Lockout is the number of seconds a machine stays locked after a team member uses Emergency Stop on a running wash, so a stray signal cannot restart it straight away. It is 10 seconds unless you change it, and can be 0 to 300. Select Save Configuration after changing it. See Lock, unlock and force-stop a machine.

Track progress in the Setup Guide

In the Setup Guide step Bring your Stormboxes online, each machine shows Claimed, Enabled and Relays assigned. Relays assigned turns green once your installer has saved the wiring settings. The step is done when every machine is claimed and enabled. For a machine that has no Stormbox, select No Stormbox.